Bentley Continental Key Fob Troubleshooting Tips
The Bentley Continental is a truly stunning car to drive. Its brushed metal accents the center stack. Beautiful wood and leather are used to cover the interior. Its formidable W12 engine produces 552 break horses of power.
The Continental key fob features rubber seals that prevent water from destroying the electronic chip. If it is submerged in pure tap water, it will be fine. However, prolonged exposure to saltwater can harm it.
Keyless entry system
Bentley Continental is equipped with keyless entry, which allows you to lock and unlock your vehicle using remote control. This is convenient and will be able to save time. There are a myriad of reasons your key fob might not function properly. Some of these include a dead battery, water damage or receiver module issues. In certain cases, the problem could also be caused by a malfunction in the internal chip.
The key fob has been sealed with rubber to keep water from entering the electronic chips. The key fob can get wet when exposed to soapy or salty water. This could harm your chip. It is vital to clean the key fob and let it dry completely prior to placing the battery back. If the keyfob won't work after cleaning it and drying, it's probably defective and needs to be replaced.
The battery of your Continental key fob features clips made of metal that keep it in place and complete the circuit. If the clips are loosened or corroded, they could cause contact problems. Check the battery contacts to ensure they are clean. Also, ensure that the battery is securely installed. Test the spare Continental Key to determine if it works. If the key is damaged then you can reprogram it using an OBDII scanner.
Battery
The key fob contains one small battery that is the size of a coin. When it is dead, the remote does not work. This is a simple issue to identify and can be fixed in a few minutes. The battery may also be damaged by water, which will require replacing it. There are several reasons for the key fob to not function, including worn buttons, faulty battery contacts, signal interference or the receiver module is dead. It is possible to reset the system by disconnecting the 12 Volt batteries for a few moments. This will allow the system to reset itself. Remove the negative cable first, then reconnect the positive.
The battery inside the Bentley Continental key fob will last up to four years depending on how often you use it. The battery is held by metal clips that keep it in place and complete the circuit. The clips should be tight however if they're not then the remote won't function properly.
If the Continental keyfob is exposed to clean water from the tap, it must be dried and cleaned with a paper towel before reinstalling the battery. If the chip is exposed to salty or soapy water, it could become damaged. In this case you'll have to purchase an entirely new key fob.
Water damage
David believes there are any major mechanical issues on this Continental. There is some surface corrosion that has occurred when the wheels have been exposed to road grit. The boot is roomy and practical with a factory warning triangle strapped to the floor, and the space-saver spare wheel as well as a the standard Bentley toolkit under the false floor.
The key fob's chip is protected by rubber seals, which will allow it to function even if it's wet. The chip may be damaged by prolonged exposure to water. It is advised to remove your key fob out of your pocket before you go swimming, kayaking or rafting.
If your key fob was covered in soapy water from the washing machine or submerged in ocean water at the beach, it may be worthwhile to get it back by cleaning the chip using isopropyl ethanol or electronic cleaner. If the key fob doesn't work after drying and cleaning, you may need to replace it. If The Keylab looking for a Bentley Continental key fob, make sure to select one that is water-resistant and specifically designed to work with your vehicle.
Fault diagnosis
The Bentley Continental keyfob enables you to lock or unlock your vehicle with a single click. This system is extremely convenient and provides security and safety while driving. However there are several things that can be wrong with your key fob. Some of the most common causes include a dead coin battery water damage, signal interference and a defective internal chip. If the key fob is not working there are a few troubleshooting actions you can take to pinpoint the problem.
The first thing to check is the battery. Check that the battery is correctly inserted, and all metal clips are in the proper position. If the clips aren't in a good position they could cause the battery to not get a good connection and won't function correctly. Furthermore, the retaining clips should be clean and free of corrosion.
A weak car battery is another reason that causes the key fob to fail to function. The 12 volt Continental battery must be in good working order to communicate with your remote keyless entry system, and the rest onboard electronics. Examine the fuses, and when necessary, recharge the battery.
The Bentley Continental key fob sends signals to the receiver module, which is within the ignition barrel. If the signal is not received, the engine will not start and an alarm will sound. If the Bentley continental key fob still not working, seek help from a professional to resolve the issue.